Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
Presented here down the page you'll find some exceptional answers all about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bathtub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have actually certified yourself for the work and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will assist you mount a new tub in your shower room if you have actually already purchased a brand-new bathtub and don't require to change the plan of your previous water pipes.
Your tools as well as product list should comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is detach the water. After doing so, activate the taps to drain any water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former kind ought to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub up until the spirit level checks out level.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water supply as well as check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and additionally check the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the tub has actually been used a minimum of when as this will settle it right into its last position.
Getting ready for the Installment
Firstly, the supporting structure provided with the bath should be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with moisture and feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the motion experienced when the tub is in usage. The sealant can crack rather early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub? Write a remark down the page. We would be interested to hear your views about this review. We are looking forward that you come back again before long. I beg you take the time to distribute this blog entry if you enjoyed it. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Estimate
Report this page